The square triangle can indicate whether the blade is off or not.
Constant use of your saw head, moving from place to place, cutting different materials and all other factors can lead to misalignment of your saw blade and other equipment. Some mitre saws even come out of the box with a misalignment!
If you have alignment problems, you can get your square saw yourself without professional service. These are the steps you need to follow to saw the saw and support mechanism:
- Sawing machine
Remove sawdust and other particles with a mitre saw. This debris can affect the saw’s levelling process and possibly cause displacement. If you are not in the habit of cleaning the saw after each use, it may be time to change your habits and start doing so to avoid extra maintenance.
You can use an air compressor with an air nozzle at the end of the hose to blow sawdust out of any part of the tool. If you are on holiday in the shop, you can also use it to remove most of the sawdust from the saw. Wipe the whole unit with a clean cotton cloth so that you can work with a fresh slate. Be sure to suppress the increase in reed when cleaning the reed.
- Control sheet .
Before resetting or aligning the saw in its original position, it is advisable to look at the saw blade to see what it looks like. Clean it if it is not clean and sharpen the knife if it has become dull before proceeding to the next step. By using cleaning agents such as Boeshield stain and rust remover you can reduce or eliminate step formation.
If the saw blade is deformed or even broken, replace it before you start aligning the saw blade. Any deformed or warped part of the blade can disrupt the process and make correct alignment impossible. All you have to do is replace your damaged knife and you can continue.
- Alignment of tables
Most people who use mitigation saws today will put them on their desks. Chances are that you have a table for your saw, use it at work, or that you are looking for one for your saw!
The table is not easy to break, but due to its use and age it can become misaligned over time. However, you can adjust it to be flat. Just put a ruler on the table and see how it is measured according to your standards. When switched off, consider replacing this part of the shaft or adding a small shim to restore a flat surface. You can also check the deviations with the naked eye, but this is not as reliable as the guideline rule.
- Alignment of the fence
Once the table is set, you will need to set up a fence for your sledgehammer. The stop is located at the back of the table and serves to support long materials during cutting. You can check if the fence needs straight lines. Place a straight ruler along the length of the fence and then look for areas that are not square.
If the fence is not square, loosen the screws holding the fence and adjust it until the fence is square. As soon as it’s acceptable, put it back in place. Don’t forget to place both sides of the fence independently because they are not necessarily on the same line.
- Adjustment of the angle of inclination of the miter
It’s time to put your circular saw at the right angle. First of all, the blade angle must be set to 0 degrees. Then also set the mitre angle to 0 degrees. The meter should be at right angles to the fence. Place a combination square or rafter square on the table and make sure it is a square. One of the edges of the square must be attached to the front of the fence. Now lower the saw to the lowest position. Slide the bracket over the side edge of the leaf. In order to gain access to the side of the blade, it may be necessary to lift the blade protector.
At this point, one side of the square must point to the side of the sheet and press the other side firmly against the stop. Check the distances between the blade and the fence to make sure they are the same. If there is an uneven opening, loosen the tab and tighten the handle. Set the angle of the mitre at a point where the blade and the fence are at right angles to each other. Loosen the screws on the stop plate to set it for accurate positioning of the saw at zero degrees.
- Tilting angle adjustment
The slope angle must then be checked in the list. Whether the table is tilted 45 degrees to the left or both, all you have to do is square the table and the 0 degree angle. Place one square along the edge, with one edge up on the table and the other edge flat on the table. Lower the saw blade and make sure that the saw blade protector is up.
Move the bracket towards the leaf until the vertical edge and the leaf are aligned. Check whether there is a gap between the square and the blade. Loosen and adjust the tilt angle adjustment knob to adjust the tilt angle when a deviation is detected. Make sure that the square and the saw blade are aligned. Tighten the handle to maintain the cone angle. Slide the clips over the bevel (your saw model determines how this is done).
- Accuracy test
When everything has been adjusted and squared, check the accuracy. Turn on the slotted saw and make a 0 degree cross section on a wide waste board. Check the accuracy of the cut with a square or spirit level. If it’s not virtuous, you have to go through this process again.
Do not attempt to adjust the circular saw in any way before disconnecting it from the power supply! Even if the saw is switched off, you may receive an electric shock from the device.
Be careful when working near the knife. Try to make sure you are in an environment where you will not be beaten or surprised when working with the blade.
how to adjust hitachi miter saw,miter saw bevel cut not straight,miter saw depth adjustment,how to adjust makita miter saw,kobalt miter saw not cutting straight,miter saw accuracy,how to square bosch miter saw,miter saw fence not straight
Disclosure: We are a professional review company & our reviews are not biased towards any of the products we review. We test each product thoroughly and give marks to only the very best that is given by our author. We are very independently owned & the opinions expressed here are our own. However, if you purchase anything after clicking the links present in the articles then we get some commissions for it which help maintaining the websites expenses like servers, security etc.