When buying or using a saw for the first time, it is important that you install it correctly to ensure that it works efficiently and effectively. An important thing to keep in mind is that you will only get an accurate cut of 90 degrees if you set your saw correctly to this specification.
Every carpenter has his or her own way of adjusting the saw for a precise cut, although many prefer a right angle of the fence to the blade when adjusting the saw. It is also possible to check the setting of the mitre saw by making a saw cut.
These carpenters want to know how accurate the saw is when they saw wood, and they don’t necessarily care if the saw is set to 90 degrees or not if it has stopped. At this point, we’re in balance with the last one.
Method 1 Mitre sawAdjustment
- Prepare the test stock for
Bring two planks, each with a perfect straight line. The best way to do this is the border crossing. For best results, the board of directors should be broad rather than narrow. The width of the boards must be close to the maximum cutting width of your router if you want to carry out a more accurate test.
- Make a cut
Make sure that the connected edges are opposite the fence. Cut out the boards. You can cut two boards at the same time. The best result is obtained when the cut is adjusted so that the material is on both sides of the blade instead of cutting the end grains. It is much more likely that the knife will bend if you just remove the skin from the last grains, which may affect the cut you make. On the contrary, there is no deflection if the blade has material on both sides. So you get a straight cut.
- Control section
Then you need to check the cut you made. Make a flat surface and place the joined edges on top, then place the ends of the cuts on top of each other. See if there are any holes. If there is a certain amount of slack at the top of the cut, this means that the saw is not cutting at a 90 degree angle.
The hole increases the error, because both signs are cut together. The size of the slot must be twice the size of your saw. This method has the advantage that the small error becomes larger, so that the accuracy can really be set more accurately. Take your saw’s operating manual with you and check the adjustment tips so that you can make the necessary adjustments.
- Confirm your results
Repeat the same cut after making the adjustment. You have set the mitre saw correctly when the cutting edges touch the width of the board evenly.
- Cone control
With a multi-cutter, it is important that the saw makes a perfect cut of 90 degrees at right angles to the table. If you are using a combination saw, you should also check the chamfer. Take the two planks, place the joined edges on the table and cut them together. As mentioned above, the insertion size must be close to the maximum cutting capacity of your mitre. Check the ends of the cut as described in the steps above and then adjust the required spiral angle until it is accurate.
Method 2 Adjusting the mitre saw
This second method is similar to the first, except that it requires a square. Set the saw to 45 degrees, place the two joined edges of the two planks on the fence and saw them together.
- Test angle.
Keep the circular saw nearby and place the square in the inner corner. Check that the edges of the square are in contact with the material. If he’s in full contact with the equipment, that’s normal. If it leaves holes on the edge of the square, it’s no good. We need to position the cutting angle correctly.
- Make a line from the cut-off fence
Turn on the fence of the saw blade to facilitate the precise positioning of the material on the saw. This includes a sacrificial fence, which is normally inserted into the fence with a saw.
The saw fence is pierced along its entire length with holes that can be used to screw the sacrificial fence. Under the fence provided by the governor there is a small space between the sacrificial fence and the saw. This space allows the sawdust to fall to the ground and not accumulate in a corner.
- Make a cut
I cut the fence after I screwed it.
- Use of a cutting line
Take a piece of dough. After positioning the layout line close to the edge, select your material. Place a line on the slot you made in the fence. The edge of the saw cut indicates the exact place where the saw table was cut.
Each of these methods can help you adjust your curve saw to get a perfect cut. If you use the saw frequently, you should do this regularly to ensure that you always get the best cuts with the tool. It doesn’t matter which method you use, as long as you get results that help you work well with your cam saw!
how to make accurate cuts with miter saw,how to make a bevel cut with a miter saw,miter saw tips and tricks,how to adjust a miter saw for accurate cuts,ryobi miter saw not cutting square,miter saw tune up,miter saw uneven cut,kobalt miter saw not cutting straight
Disclosure: We are a professional review company & our reviews are not biased towards any of the products we review. We test each product thoroughly and give marks to only the very best that is given by our author. We are very independently owned & the opinions expressed here are our own. However, if you purchase anything after clicking the links present in the articles then we get some commissions for it which help maintaining the websites expenses like servers, security etc.